1 Ton Capacity Gas Steam Boiler

1 Ton Capacity Gas Steam Boiler

The main data processing means is automatically shutdown when the boiler pressure is too high, the combustion system will stop working; operating power may also be changed, single-stage or two-stage combustor; can adjust the amount of oil (or gas) to achieve proportional control, whereby depending on the steam pressure adjusting load operation of the burner, to ensure safe operation of the boiler.

If you know a little about chemistry, you may know that the sulfur content of oil and coal is roughly equal, but ask what low-temperature corrosion of oil-fired boilers is much more serious than coal-fired boilers, for two main reasons:

1. 90% of ash in coal-fired boiler, especially coal powder furnace, is taken away by flue gas, sulphuric acid steam formed in flue gas is absorbed by fly ash in flue gas, so that sulfuric acid vapor in flue gas is reduced, and about half of sulfur remains in ash when coal is burned. When the oil is burning, the sulfur content in the fuel almost all changes to the ash in the SO2, fuel, the fly ash in the flue gas is very little, and the adsorption ability to the sulphuric acid vapor in the flue gas is very weak.

2. The hydrogen content of oil in the oil-fired boiler is about 11%-12%. The combustion of each ton of fuel oil can produce about 1 ton of water vapor, and the partial pressure of steam in the flue gas is higher than that in the case of coal-burning.

Energy-saving measures and methods of industrial boilers which industrial boiler energy-saving measures and methods which 1, to increase the capacity and improve the thermal efficiency of boilers and inefficient small compared to the large-capacity high-efficiency industrial boilers, can greatly improve the utilization of energy rate, so as to obtain greater economic benefits. Meanwhile, the cogeneration project enables conversion of exhaust or extraction steam turbine for heating, not only can reduce the loss of turbine exhaust steam, but also help to save coal resources. Industrial boiler thermal efficiency of China's low is a fact that can not be ignored, usually operating efficiency even lower. Therefore, improving the efficiency of industrial furnace hot pot, is crucial for energy savings. In one aspect, by improving the quality of the insulating material, thicker insulation, heat loss can be reduced. On the other hand, the use of secondary air system, can facilitate a more complete combustion of fuel, the effect is very significant. 2, the heating surface to reduce coking and fouling of industrial boiler during running, prone to coking, fouling phenomenon, resulting in increased and then decreased local resistance to the flow cross section. Not only conducive to smoke, but also so that heat transfer is reduced, further increasing the temperature of the flue gas. Industrial boilers and cleaning agent has a good cleaning effect, can be put in the appropriate amount sublimation decompose at high temperatures, with the heating surface of the coke, slag and contacts a chemical reaction can be automatically off after decomposition. Meanwhile, a method of periodically purging is also more effective in the early formation of fouling was loose state can be cleared periodically sootblowing. If the attachment is too long time, will translate into close like fouling, thus increasing the difficulty of cleaning up. 3, to ensure the quality of coal and industrial coal-fired boilers with coal is crucial, its moisture, volatile content factor for the speed of fire, as well as affecting the combustion temperature is extremely obvious. Maintain proper moisture content can be reduced with reduced leakage occurrence of coal and fly ash, coal seam and helps enhance the evacuation ventilation. If the moisture content is too high, will affect the speed and the temperature in the furnace, heat loss will be increased exhaust smoke. Industrial water boiler heating surface for scaling impact of large scale for each additional 1mm, the overall thermal efficiency of the boiler will be reduced by 3%. 4, many factors affect the lower exhaust gas temperature industrial boiler flue gas temperature, within the course of the economizer scale, cleaning up soot neglect of smoke in the furnace wall channeling smoke, poor treatment effect, can cause elevated exhaust temperature. On the one hand, to deal with the heating surface appears slagging, fouling and scale phenomena take timely measures to eliminate, minimize or avoid their presence. On the other hand, on the rear of the boiler heating surface is improved or increased. Industrial boiler flue gas temperature, objectively reflects the utilization of exhaust heat. But not as low as possible, the exhaust gas temperature is too low but not conducive to the normal operation of the boiler.

20th Meeting of the Standing Committee of People's Congress of the fourth Jinzhong City, approved the Thirteenth People's Congress Standing Committee of Shanxi Province, the seventh meeting since January 1, 2019 the formal implementation of the "Jinzhong City coal pollution prevention and control regulations "(the" Ordinance ").

1, Municipal People's Government shall determine the total amount of coal required control objectives, the development of coal-fired reduction and clean energy transformation plan and organize the implementation, reduce the proportion of coal in primary energy consumption structure in accordance with the requirements of the provincial government and city environmental protection.

2, Municipal People's Government shall designate built-up area for the city ban on coal zone and gradually extended to improve the quality of atmospheric environment on request. Counties (cities, districts) need to improve the people's government should ban on coal zone demarcated according to the ambient air quality.

May, ban coal-fired power plant area, central heating stations and raw coal units shall establish a coal purchase and sale of its products archives management, and self-purchase contract is signed or change within fifteen days, the number of coal procurement and information submitted to the seat of county government department in charge of energy.

6, city and county (city, district) people's government should promote the local conditions of the administrative regions of central heating, coal to electricity, coal gas and other clean energy alternative to coal-fired work. Encourage towns, rural areas to promote the use of clean energy living stove.

9, city and county (city, district) people's government should strengthen the management of civil bulk coal regions other than coal ban areas, to determine the clean coal supply companies, establish and improve civil cleaner fuels coal procurement, storage, supply mechanism to protect the clean coal supply.

10, city and county (city, district) people's government market supervision and management departments should be included in the annual coal-fired coal sampling plans to strengthen quality supervision and inspection, and to the public inspection results.

11, coal-fired power plants, district heating stations and boiler units to use raw coal output and single kiln production process should be in line with national standards and local regulations or policies. Any unit or individual may manufacture, import, sale and use do not meet environmental protection standards of boilers, furnaces.

12, supporting the construction of coal-fired units should use air pollution control equipment and facilities to maintain normal and stable operation, pollutant discharge should meet the standards set by the state and local levels. Encourage the use of coal-fired units to implement ultra-low emissions transformation in accordance with the requirements of environmental protection.

Free Chat

About Us

Contact Us