609, why the 14 ton fired steam boiler is replaced by electric heating gas steam boiler steam boiler is replaced why the electric heating gas furnace compared with the steam boiler steam, and the higher production requirements, pressure increases with increasing temperature. In recent years, new thermoelectric organic heat transfer oil furnace is also known as heat transfer oil furnace. we usually referred to as gas steam heater. it combustible gas and electrical energy to thermal conduction of the heat medium oil high oil outlet to 400c, heat device connected to the hot water more environmentally friendly and energy saving compared with the steam boiler, saving up to 40% to 55% oil furnace using electric heating and the conductive loop. different steam, the steam is directly discharged after use, heat can not be recovered heating stable, accurate temperature control. gas steam boiler and the heat transfer pipe are stable, unlike a steam boiler steam temperature fluctuations in the system, gas and steam electric furnace facilitate automatic control microcomputer electric heating oil heater low and high temperatures are secure, gas and steam heated to 340 degrees at normal pressure, does not evaporate. steam reach the same temperature, the saturation pressure 14.593MPa. hot water boiler must be in order to achieve a certain pressure High water temperature. If you want to get a temperature of 280 degrees Celsius, the pressure should be reached 6.412MPa. Therefore, gas steam heater has a good safety performance heat transfer oil furnace electric heating with low cost, low investment, easy to manufacture and so on. due to the low heat transfer oil furnace operating pressures, significantly easier to manufacture than the steam boilers and hot water boilers, low cost, small investment. in general, class E with twelve kinds of boiler or pressure vessel manufactured qualified manufacturers have the ability to produce hot oil furnace .609,
Gas-fired heating is to protect human health and indoor warm natural gas boiler with natural gas, LPG, city gas and other gaseous fuels for fuel combustion in the furnace put out heat, heat the pot of water, and it vaporized into steam the thermal energy conversion device. Water pan (drum) is continuously released from the combustion of a gaseous fuel energy to heat the furnace temperature is increased and produce steam under pressure. Since the boiling point of water increases with increased pressure, the pot is sealed, the expansion of water vapor generated inside the pressure limited thermodynamic formed, strictly speaking, the 14 ton fired steam boiler is heated in water at constant pressure saturated steam drum regasification water formed, is widely used as an energy source. Gas-fired heating is to protect human health and indoor warm, so the choice of natural gas boiler when security issues are important, but the quality can not be ignored, and only with good quality, just more comfortable when in use, some of the services also can do better, choice of heating is customer satisfaction. Learn natural gas boiler certainly need to know the sales of the product, and if it shows good reputation natural gas boiler in the comprehensive aspects are still very good, worthy of consumer choice, performance, and thermal energy conversion can consult, when such use was not there will be problems when installed, do not worry voltage is not enough. Gas boiler shutdown method: after stopping a powder, a duct for 5 minutes and then purged to stop the gun. Oil gun should be purged one by one, not at the same time purging multivessel oil gun. After completion of purging gun oil, natural ventilation of the boiler furnace 5 to 8 minutes, 20 ~ 30% of the air volume is not less than the rated load. To exclude combustible material remaining in the furnace. The fuel gas-fired steam boiler can be divided into natural gas, city gas steam boiler, a steam boiler coke oven gas, LPG and steam boiler; according to the structure can be divided into vertical and horizontal steam boiler steam boiler. Gas boiler shell type three return all wet back downstream pyrotechnic pipe structure, the combustion flame in the combustion chamber large positive pressure, fully extended, low combustion heat load, the high heat of combustion efficiency, effectively reducing the exhaust gas temperature, energy saving , more economical, and a waveform furnace threaded pipe structure, i.e. increase the strength of the heat absorption of the boiler, but also to meet the needs of thermal expansion of the heating surface, scientific and rational, and durable.
Still 8 cultural and creative industrial park is located in the Chaoyang District, Beijing, Bali Zhuang Chen Lin, No. 2, construction area of 493,300 square meters. Surrounded by quintessence of Court, Red Sandalwood Museum, Shanxi Museum and other famous attractions. Due to its special geographical location, has very stringent requirements for providing heat boiler plants. Carefully selected to finalize cooperation with our company, signed a two He Lide series complete condensation pressure hot water boiler.
Steam boiler has brought great convenience to industry. Steam boiler has driven the development of the times. The following is a brief introduction to the structural characteristics and working principle of steam boiler. Steam boiler is a machine that mainly produces steam, and many people use it, but many of them do not know much about its structure and working principle. It makes use of coal, oil, natural gas and other water-tube steam boilers with limited capacity and pressure. There is a large desire to space, and easy to arrange, steam boiler in a variety of forms. Water is heated in the drum into steam, and the heat emitted by fire in the furnace is the principle of a steam boiler. Work of steam boiler Principle:
1, the heat generated by pulverized coal combustion in the furnace is first absorbed by the water wall through radiative heat transfer, and the water boiling of the water wall is vaporized, producing a large amount of steam into the steam drum for steam separation (except for direct flow furnaces). The separated saturated steam enters the superheater and continues to absorb the flue gas heat at the top of the furnace and the horizontal flue and the tail flue through radiation and convection, and enables the superheated steam to reach the required working temperature. The steam boiler for power generation is usually equipped with a reheater, which is used to heat the steam after the high-pressure cylinder does work, and the reheat steam comes out of the reheater to go back to the middle, and the low-pressure cylinder continues to do the work to generate electricity.
2. When the pulverized coal stove is working, The position of the center of the flame will affect the amount of evaporation, generally speaking, if the center of the flame is low, the amount of evaporation will be large, and the position of the center of the flame will also affect the temperature of the superheated steam or reheated steam, as well as the high value of the flame center and the small amount of evaporation. When the flame center is low, the superheated steam, especially the reheated steam temperature, will be low and vice versa.
3, the arrangement of burners, as far as coal powder furnace is concerned, there are many kinds of combustion modes, such as front and rear wall, tangential combustion, double tangential combustion, and so on, each of which has its own characteristics. The influence on steam can not be directly determined because the same furnace can not apply the above-mentioned arrangement methods at the same time.Free Chat
Copyright © 2020.Company name All rights reserved.