2400 Kw Gas Fired Boiler

2400 Kw Gas Fired Boiler

Our company attaches great importance to the quality of wine, winemaking process steam requirements provided very strict, party fast 2400 kw fired boiler provides fully meet our needs, give us a brewery to provide strong support. --customer feedback

With the increase of air supply volume, the mixture of oil mist and air is improved, which is beneficial to combustion. However, if the air volume is too large, the furnace temperature will be decreased and the incomplete combustion loss will be increased. At the same time, the heat loss of exhaust gas will be increased and the power consumption of the fan will be increased because of the increase of flue gas. If the air volume is insufficient, the combustion will be incomplete, resulting in carbon deposition at the tail, which is prone to secondary combustion accidents. Therefore, each 2400 kw fired boiler should pass the thermal efficiency test to determine its economic air volume at different loads. In practice, the stoves usually take into account the ignition of the nozzle and the carbon dioxide or oxygen content in the flue gas. Content to adjust the supply air volume. If it is found that the combustion condition of a nozzle is not good, or if the atomization plate with different aperture is replaced, the air pressure of the supply duct should be kept unchanged, and the opening degree of the duct baffle of the nozzle should be adjusted to normal combustion. If the fuel quantity changes due to the change of the oil pressure in front of the furnace, the opening of the fan baffle should be adjusted to achieve normal combustion by changing the air pressure and air volume of the air supply duct when it is necessary to adjust the supply air volume.

3) the observation and analysis of all kinds of flame when adjusting the fuel oil. Generally through the fire point adjustment and flame center adjustment to complete the flame adjustment. The ignition point of the oil mist should be close to the nozzle, but there should be no tempering. Early ignition is beneficial to complete combustion and stability of oil mist. However, the fire is too early, too close to the nozzle, easy to burn the nozzle and furnace wall to determine the mouth. Furnace temperature flying oil varieties and atomization quality, as well as air volume, wind speed and oil temperature, will affect the distance and proximity of the ignition point. So if you want to adjust the ignition point, you should find out the cause in advance, and then take targeted measures. When the boiler load is constant and the oil pressure and oil temperature are stable, Should be based on the ignition point wind speed and wind distribution situation.

New coal fire late, often appear off the fire bed fire, fire away from coal gate about 0.6 ~ 1.Om, burning furnace is not strong, high ash carbon content. For existing furnace arch structural problems, from improving fuel fire conditions, improve furnace temperature begin to transform the 2400 kw fired boiler. After the furnace arch after the transformation, the people stove fuel from coal gate 0 · 3mRP fire, the fire bed combustion intense flame full of good, strong rotation. Since lowering the front arch, the arch extended, reduced to about 1 2 throat formed between the arch of the original pitch. Where the enhanced mixing flow disturbances, reorganized stream, enhanced combustion furnace, to effectively improve the temperature of the entire front region and the arch of the furnace, to reach 1400 degrees, the condition of the fuel to improve ignition. 2. The ignition point of coal in advance, the temperature of the furnace to improve the ash carbon content decreased. Smoke swirling mix and strengthen the separation of coke particles in the flue gas, so that it falls on the fire bed and the new layer further fuel burn. Flue gas also strong swirl in the flue gas CO, H2, CH4 and other combustible combustion gases, thereby improving the thermal efficiency of the boiler is more than 4%. But also improve the boiler output to meet the needs of the production of steam, reducing environmental pollution, expanding the scope to adapt varieties of coal.

How much the price of Yichang electric steam 2400 kw fired boilers for textile mills in the production process, printing & dyeing, drying and other procedures are required to use steam. So, say mills for boiler steam demand is great. For textile mills, before purchasing a steam boiler must be to their own policies for local electricity companies and environmental requirements are to be understood. Recently, there is a Yichang textile enterprises purchase a steam boiler fast boiler for the production of advice that he is the actual local situation is through the gas, but the gas source for hard to apply, but the local price is not high Therefore, after careful communication, it suggested a change in Yichang textile companies can purchase electric steam boilers. In this case, it is still in line with local realities of the situation. After a simple accounting of fast boiler technician, electric steam boiler plant with two 2t it is to meet the needs of current production, now the entire purchase price in Yichang mills around 360,000.

Free Chat

About Us

Contact Us