Condensing Gas Hot Water Boilers

Condensing Gas Hot Water Boilers

Preparation and method for measuring the moisture content of the flue gas of the boiler before the boiler purchase this product knowledge and understanding, the present, it is necessary for two reasons, first, it is the site of important product and the main key one word, and second, the products are widely used, why we have these conclusions and specific requirements. Meanwhile, I hope that we can be taken seriously and, in order to have learned well and apply their knowledge to practical work flexibly. Is there some preparatory work before the boiler 1. buy? Boiler products to buy, this is an important job, and need to be taken seriously, but also want to take into account all relevant factors, in order to have accurate judgments and the correct choice, a good choice to avoid mistakes. Before carrying out this work, is the need to do some preparation, use of the product to the environment and have a clear understanding of the requirements and learn about product origin, specifications, technical parameters, materials, quality, price, service and product manufacturers these and other basic information, in order to compare and consider, then, the right to choose their own products. 2. whether Sheung Shui before the boiler starts have specific requirements? From a professional point of view, Sheung Shui before the boiler starts, there are some basic requirements, which specifically is: If the condensing hot water boilers, the water speed before it starts not too fast, not be less than the winter time Sheung Shui 4 hours, in other seasons upper water time of not less than 2-3 hours. And, at the beginning of the water, its water speed to slow. If the boiler is cold, it's inlet temperature in the range of 50 ℃ -90 ℃, and the difference between the water temperature and the temperature of the drum wall into the steam drum, not greater than 40 ℃. 3. What is the chain boiler? Chain boiler, which is a particular kind of a boiler, a higher degree of mechanization layers fired boilers, the time the track grate with a chain similar to these so called chain boiler A boiler. Further, it is a pre-boiler, the coal combustion process is completed in the movement. Advantage of this kind of boiler, the combustion condition is stable, high thermal efficiency and easy operation, in addition, its low concentration of dust emissions. However, it should be noted that the moisture content of the larger, more ash and strong coking coal, not suitable for this kind of boiler for combustion. 4. How the moisture content in the flue gas boiler measured? Determination of moisture content in the boiler flue gas, which is the weight measurement method, condensation method, and three psychrometer, and the moisture content of the flue gas is typically in the volume percent of water vapor in the flue gas content to represent. If dark gravimetry, need to use hygroscopic agent, the hygroscopic agent used is calcium chloride, calcium oxide, silica gel, alumina, phosphorus pentoxide, magnesium perchlorate and the like.

Mill steam boilers to reduce pollution which method 1, leak checking and maintenance of protection: 2 mm steam leakage will cause energy losses of more than 10 tons of coal each year do? When you do not use it, you can turn it off to save energy. For water, steam and compressed air leak survey and routine maintenance, cost very little. 2, the non-contact cooling water in repeated use: Since the non-contact cooling water temperature and the quality is very good, it can be reused for desizing, scouring, rinsing and other processes. Three best source of cooling water is regenerated: sintering machine, a pre-link and compressor systems. The plant water recovery system may be installed, pipes, valves, storage tanks, and control systems. 3, reuse of steam condensate: textile mills require large amounts of saturated water vapor in the dyeing process, wherein a portion of the condensate is converted to its high temperature and purity. Water can be pumped back to the boiler to form a new steam. For those who buy steam from suppliers, or boiler is located away from the dyeing process, the condensate can be used as water washing or desizing. 4, pre-treated wastewater reuse Procedure collected bleaching, mercerizing machine, the water can be reused in other programs, there is no direct discharge of wastewater. 5, hot wash water is recovered from the hot gas in the dyeing process, large amounts of hot water are used to wash. Heat the washing water can be collected by the system plate heat exchanger to preheat the water to be sent to the next washing. 6, pre-screened coal enterprises should introduce screening spiral coal boiler technology to selection of raw materials. It is possible to improve the media tell the good, the bad quality of proportion, to avoid loss of small volumes of coal and coal calorific value. 7, maintaining steam traps traps can help maintain effective delivery of the steam plant. The valve is removed from the steam pipe and prevent further condensation water, so as to avoid heat loss and reduce fuel consumption. 8, pipe insulation pipes, valves and flanges, valves and flanges experience hot waste of resources, reducing efficiency. Steam delivery device insulated to prevent vapor loss is an inexpensive, energy-saving method of .9, the heat recovery boiler chimney smoke at a temperature of 360 deg.] C, and sometimes directly discharged into the atmosphere, there is no heat recovery. In fact, this heat can be used to preheat boiler water, steam or create a new steam system. 10, optimization of compressed air systems consume a large amount of compressed air in many parts of textile machines Mills. These instruments are prone to leakage, particularly in a threaded joint, rubber joints, valves, automatic regulator, the inflatable device and the old gasket. In addition, the use of compressed air pressure is usually based on the maximum pressure setting; reduce this pressure is feasible and would not have any negative impact manufacturing.

There are a few big happy event in life, conclude, than the following: drought every winter rains, foreign land refresher, the wedding night, pass the examination, as well as being hit Awards. In March this year, planned by the fast Boiler Group hosted the second session of the boiler room] [best photo contest Huobian country! Fans actively participate in activities perfect ending. Gain a lot of excellent photographs, the Group established a review panel for the competition each photo a rigorous review, and ultimately selected a first prize, two second prize, third prize 3. In addition, the panel of judges based on the results of online voting to elect Choice Award six.

The steam boiler can be divided into three kinds according to the fuel (electricity, oil, gas), such as electric steam boiler, oil steam boiler, gas steam boiler, etc. According to the structure can be divided into vertical steam boilers, horizontal steam boilers, small steam boilers are single, double-return vertical structure, large-scale steam boilers are mostly three-way horizontal structure. If according to the classification criteria above, there are a lot of steam boilers, take an ordinary fast-packed 4-ton steam boiler. Water is heated into steam in the drum and heat is emitted by fire in the furnace, which is the principle of the steam boiler. Steam The combustion part of a steam boiler consists of a chain grate and a drive device, together with a combustion chamber composed of a boiler rack on the grate frame. Surrounded by refractories. Coal from coal hopper, there are coal gate to control the thickness of coal seam while sealing the front of the air. The lower part of the combustion chamber is the place where the blast enters. This steam boiler has great resistance and needs forced blast. The cinder of a steam boiler, discharged from the back of the grate through Eagle's mouth iron and sent out of the furnace by a slag extractor. Steam boiler flue gas from the back of the boiler, by the steam boiler drum one-way smoke pipe forward, from the two-way smoke pipe back to the rear, then into the dust collector to separate ash, and then through the induced fan from the chimney exhaust Out. The above is the working principle of steam boiler, of course, the operation of steam boiler without other equipment, such as the induced fan not only undertake the task of exhaust flue gas, but also the steam boiler negative pressure operation necessary. There are also pressure vessels, thermometers, safety valves, pressure gauges, pumps, steam pumps, etc. All are essential for steam boiler work. Pump leak problem. The actual output flow rate of gear pump is smaller than that of theoretical flow due to the leakage of gear pump in the process of operation. The main leakage channel of gear pump is through the gap between the two sides of gear and the cover plate on both sides of the gear, which is 75% / 85% of the total leakage of the pump. Radial clearance leakage between gear top circle and inner hole of pump; clearance leakage through gear meshing. Because of the leakage of gear pump, the output pressure does not go, which affects the range of use of gear pump. In order to solve the problem of low output pressure of gear pump, the way of adding floating sleeve or elastic baffle on both sides of gear pump is adopted to reduce the leakage of gear pump and improve the output pressure of gear pump. Radial force imbalance problem. In the working process of the gear pump, the pressure on the outer circle of the gear is not equal, which results in the radial unbalance force at the shaft and bearing of the gear. This radial imbalance will accelerate the wear and tear of the bearing, reducing the bearing The service life also may cause the gear shaft to deform, causes the tooth top and the pump body inner hole friction, damages the pump body, causes the pump not to work normally. The common solution is as follows: (4) opening pressure balance slot on pump, leading high pressure oil to low pressure area, but it will increase pump leakage and affect pump volume efficiency; (2) reducing the size of the pressure chamber, reducing the pressure area acting on the gear teeth, and thus reducing the radial unbalanced force.

Free Chat

About Us

Contact Us