Multi-fuel steam boiler protection water protection Fuel steam boiler: boiler water level gauge plate supporting one to two, should always be compared with each other, findings indicate inconsistency shall be corrected immediately. Class water level should be flushed, to determine their true level. While the water level comes electrode rod can accurately capture level signal to an alarm or a pump control. A steam pressure protection, the pressure controller: selection of high sensitivity of the pressure controller, the pressure is high, or low levels of signal to the electrical switches, automatic control chain protection or other control lines. Using pressure controllers and electrical contacts, the vapor pressure can overpressure alarm; single adjustable pressure controller or dual fire burning fire the actual operating pressure. 2, the safety valve: safety valve is the last line of defense to protect the boiler, the boiler pressure exceeds the limit, according to the set pressure relief valve design with the school, the exhaust steam pressure relief, to ensure the normal operation of the boiler. Flame protection: imported burner having a flame protection device, combustion function is to detect, when the ignition failure or extinguish combustion middle, immediately off the burner into the oil (gas) solenoid valve, the blower continues to operate at this time, the furnace was purged of residual internal combustible gas, after 20 to 30 seconds purge, and various auxiliary blowers automatically cut off power, the boiler operation stops. Self-locking power failure protection: Under the emergency power supply is interrupted, the boiler shutdown immediately self-locking, if the current power is restored, the boiler will not start at any time, you must reset release self-locking, to re-start the ignition.
Off state of the oil-fired boiler and approach the customer Q: oil-fired boiler flameout what state? How to determine whether the fuel gas boiler flameout it? Henan A fast boiler Company: Table fuel gas boiler furnace pressure instruction value suddenly increases; the furnace black, can not see the flame hole to see the fire; sound disappears combustion furnace; issued extinguishing the flame monitor signal; temperature, pressure abruptly fall, after the water level decreased and then increased, and so are flameout phenomenon. Auxiliary flame caused by an accident, such as a fan, blower power interruption, there is an accident signal emitted; fuel supply is interrupted as a result, oil-fired boiler fuel pressure is reduced to zero. If only a single burner flame, the furnace may also occur flame center deflected off the burner pressure changes; fuel supply is interrupted as a result, the extinguished burner pressure or hydraulic indication may drop to zero, while the other run burner fuel, gas pressure. After this occurs, must be timely treatment to ensure safe boiler. Customer Q: oil-fired boiler flameout, how can I deal with? Boiler Company Zhoukou City lofty Answer: Once a flameout must immediately cut off the fuel supply to the furnace, close the solenoid valve supply (supply and return oil), and then close the fuel supply valve in each operation of the burner. Operation action to be fast, so as not to continue or resume the supply of fuel, causing a risk of malignancy. At the same time, to identify the cause of the boiler flame, troubleshooting discovered, and then start doing the preparatory work. Before starting, we should strengthen boiler ventilation, purge, purge time is more than 5min, then procedures ignition. When the ignition is prohibited sent directly to the high temperature furnace fuel ignition without using an ignition device, in order to prevent dangerous accidents furnace. If due to fan failure caused when the flame, should quickly close the fuel supply line valves each, paying particular attention to the valve not tightly closed due cause fuel leakage. Meanwhile, according to emergency shutdown processing method for ventilating and purging of the furnace and the flue. After the fan resume operation, then step ignition. If only the burner flame, simply close the fuel supply valve to the burner, off throttle small oil-fired boiler, to identify and troubleshoot, and then re-ignition process the ignition. Be sure to quickly deal with properly in order to ensure the safe operation of the boiler.
Using Ultraten wings condensation boiler technology has greatly enhanced heat the heating rate; silicon alloy material design to achieve the depth of the condensing heat exchanger, high efficiency, high heat transfer speed. "APH the T7" ready to use the factory mode, the system design is simple and clear, i.e. security that is used, the best burner performance debugging the factory, the user can simply set up at the installation site, connected to gas, water, to a flue , it covers an area of greatly reduced.
Steam boilers common faults and submersible pumps fast boiler's Henan Xiao Bian introduce a common steam boiler failure problems common faults and submersible pumps steam boiler water level is with you, the causes and solutions to a steam boiler water level is a common problem its reasons: 1, the water level is too low installation; 2, water, a water pipe connected too small; 3 have a water level or a low level display instrument automatically when the water level on only one boiler; 4, drainage water gauge no grounding drain cock; 5, the drum water level is an effective, other water damage; 6, the tap water is screw fixed; 7, the tap water gauge leak, leaking; 8, water gauge false water level on a display; 9, the drum water level in the two water gauge level of inconsistency; water glass is often broken; 11, water glass is no guard; 12, the water level is low level indicating no glass panel represents red; 13, level glass plate is dirty, the water level observation is unclear. The main reason is because of 1-4 above design, installation or alteration of dislocation caused. When the steam boiler with a low water level status is when the drum water level is only one case, because the internal balancer lowland water's leakage short circuit (can not be detected at that time), causing lowland water level is high water level appears ( the so-called full of water), while the water level on the drum have shown that low water levels (and may even see the water level), then the fireman because they can not determine the true level of the boiler will go immediately and check the water level on the drum, it will be very serious water shortage delays container boiler accident occurred. Some even show the water level too low trust level's status, and take a lot of sewage, mistakenly steam boiler water when filled with water incident handling, acceleration accidents, there is precedent for such incidents to be investigated. Then, the above-mentioned reasons for the failure of 5-9 main problem is the boiler running for long periods of time rinse water, a daily maintenance is not carried out, resulting in water cock rust, gas, water and even the block, or insufficient packing or aging deterioration . False water level phenomenon, in addition to gas, water or even the cock pipe is blocked, but also could be vapor, the water pipe connected to the water level due to misalignment connected; steam, water tap handle installed the wrong position resulting cock closed, since there poor water quality, the water level in the boiler and false priming. Water gauge glass is broken mainly steam, water faucet centerline not aligned, the presence of glass bending stress; long glass without expansion gap; water gauge is being cold draft at window glass, and glass pipe quality was poor. Submersible pump is a mechanical and electrical integration of high-tech products. In recent years, due to the submersible pump in a sealed, insulation, cooling and monitoring technologies have made great progress, but also successfully achieved the automatic coupling pumps and water pipes, so that the large diameter submersible pump application significantly faster. Since diving save electric pumping station project investment, quick installation and maintenance, operating conditions greatly improved equipment reliability and service life improved significantly. At present, China is not only the production and installation of large-diameter 900 mm below the axial and mixed-flow pump, can produce diameter 1.4 m and 1.6 m large submersible pumps, has laid a good foundation for the promotion of technical diving electric pump station. Gao dive afraid of flooding, but also has good maneuverability advantages of quick removal and installation, able to cope with the water level soared, chestnut room flooding and other emergencies pieces, large-scale changes asked of submersible pumps. Henan is committed to fast boiler steam boiler manufacturing, product quality, reasonable prices and widespread industry praise, if you have any needs, please contact us!Free Chat
Copyright © 2020.Company name All rights reserved.