Henan italian boilers manufacturers manufacturers fuel gas combustion boiler features a contrast, combustion of fuel is a liquid fuel and fuel oil, its boiling point is always lower than the ignition point, so that fuel combustion is always performed in the gaseous state. Fuel oil particles atomized by the jet into the furnace after the furnace is heated by high temperature flue gas, gasification, and hydrocarbon ambient air encounters the oxygen gasification, a flame. Heat produced by combustion of oil particles pass a part of the gasification and combustion of oil particles continuously, until the burning ember. The smaller the diameter of oil particles, the faster the combustion of oil particles. Similarly, the oxygen required for combustion of oil particles can be supplied in time, the combustion of oil particles can more quickly. Therefore enhanced combustion of oil must do the following: 1, to improve quality of atomization, the oil particle diameter is reduced; 2, increasing the relative velocity of the air and oil particles; 3, reasonable air distribution. Second, the combustion gas boiler manufacturers Laid Henan boiler ignition gas with a high calorific value, large amount of air, can make the combustion gas, a large amount of air mixed therewith. No fuel combustion gas atomization process with the gasification process. Gas and air mixing mode, the flame length and flame temperature has a significant impact on the intensity of the combustion. Depending on the mixed mode, the combustion method of the boiler manufacturer Henan gas boiler can be divided into three types: 1, i.e., this method does not pre-mixed combustion diffusion combustion, but interdiffusion gas nozzle opening, and burned. Shao Shao stability advantages, the structure of appliance is simple, but the flame is longer, easy to produce incomplete combustion and carbonization of the heated area. 2, partially premixed combustion air prior to combustion such a way that the combustion of part of the air mixed in advance with the gas (primary air excess coefficient between 0.2-0.8), followed by combustion. The advantage is clear combustion flame, combustion strengthened, high thermal efficiency. However, combustion instability, and high combustible component of the control primary air requirements. The gas burner usually used such combustion. 3, i.e. flameless combustion air which has been uniformly mixed with the combustion gas prior to such gas required for combustion. Primary excess air ratio is equal to the excess air ratio for complete combustion of the fuel required to obtain oxygen from the ambient air during the combustion process. When the combustion gas and air mixture reaches the combustion zone can be completed in an instant.
How to pick a good quality energy saving italian boilers manufacturers after the Spring Festival, as the footsteps of spring, the weather will be getting warmer, but still occupied Henan sky haze, boiler plant today to explain how to select energy saving boiler? Energy saving boiler how to select, first look at fuel boilers. How to select energy saving boilers, first look at fuel boilers. Fuel gas-fired boiler used as bituminous coal, lignite, coal culprit is called fog and haze, so the gas boiler can not be called environmentally friendly energy-saving boiler. Fuel oil-fired boilers using heavy oil, compared to a gas boiler, has a capacity of environmental protection, but be aware that the boiler blowdown measures, and therefore there is a certain air pollution. Biomass fuel boiler is called energy saving type boiler, the main fuel is a biomass fuel particles, which fuel is free parathion, does not produce sulfur dioxide and phosphorus pentoxide combustion, and thus will not cause acid rain generation, do not pollute air, not pollute the environment, thus greatly easing the greenhouse gas emissions, to purify the air played a very good effect. Therefore, energy saving boiler how to choose? First look at the use of fuel boilers, so according to this aspect, you can determine what type of environmentally friendly energy-saving boiler.
In accordance with article 1.2 13.3.6 to 13.3.8 "italian boilers manufacturers design specifications" (GB50041-92): gas-fired boiler provided in the other buildings should be not less than 3 times the amount of ventilation, ventilation hour It does not include the amount of combustion air volume. Dangerous operating room and the like between the gas regulator, the amount of ventilation per hour, should be less than 3 times, when not meet the requirements natural ventilation, mechanical ventilation should be provided, and should be less than 8 air changes per hour accident ventilation times. Fuel pump and reservoir 45 ℃ flash point less than the underground tank of combustible oil, except that natural ventilation, the fuel pump mechanical ventilation 10 air changes per hour should times, six times per hour ventilation should depot mechanical ventilation. The above three are in each room in order to ensure exclusion of air and flammable hydrocarbon disposed a predetermined minimum ventilation rate.
Our other fast italian boilers manufacturers in the boiler industry strength already heard, through cooperation proves that our choice is correct. This water-tube boilers installed very quickly, basically no delay our production process, bring benefits to the enterprise. --customer feedbackFree Chat
Copyright © 2020.Company name All rights reserved.