Hot water boiler burner does not fire the three main reasons Henan fast boiler hot water boiler in malta will appear in the application process or as a small problem like that, a small writing today to tell you the reason water boiler burner does not fire: 1) water boiler burner nozzle does not contain oil pump will supply duct obstruction's sake, do not start the motor smoke, gas leaks and other pipeline being empty. The case of the oil pump can be pressed to start the motor in accordance with the removable tubing to check Gao, no problem when pumping oil column To spewing out. Hot water boiler is not introduced into the head oil is a reason that there is no access to the oil off solenoid valve. When the power cut solenoid valve is closed, the starter motor is no problem even if the work to do, Gao pressure fuel pump to the supply side is not easy. Only when the control board so cut solenoid valve to supply, gasoline can be eliminated. Its purpose is to avoid the exposure to gasoline with the furnace fire for light generation blasting. Generally, when the ignition, the first burner to carry out the pre-blowing, blowing clean residual gas in the combustion chamber, followed by an oil pump ignition. When the pre-blowing part, pump motor operation, cut solenoid valve disconnected from the supply, an outer fuel pump pressure Gao extracted oil solenoid valve is cut off Bunengdaoda nozzle. 2) No ignition voltage Gao connect the supply when the ignition transformer, causing pressure of about 8kv Gao and Gao pressure across the gap between the power level, cause significant flames, pilot fuel mist. When the flame lit steady, no longer have to fire ignition, flame controller flames circumstances message to the control panel, the ignition transformer termination of work to do. Gao pressure is not generated because of a fire, the ignition transformer is not connected to a power supply (or will be co-line circuit board in a loose fuse); two intermediate stages is two thermoelectric grounded due to poor soot, Gao pressure leakage, not to cause sparks. Intermediate grade electrical sparking spacing of about 3mm, electrical sparking head and the rear end of the intermediate stage spacing of about 5-7mm. Always excellent intermediate stage two electrically grounded. 3) water boiler burners to start the motor after a long low water pressure after damage, start the motor of a large pressure will gradually decrease, resulting in poor pump suction fog, sparking tough, sewage after sparking a lot of smoke, flames unstable, adjust the water pressure to start the motor useless. Head embrittlement, resulting in poor absorption fog effect, rather similar. You already understand the reason burner hot water boiler does not fire up. It dealt with the problem when your furnace?
Our company has been committed to using environmentally friendly, a paper manufacturing process cleaner way, so we paid great attention to environmental protection boilers and other properties in selected product when the boiler. The fast-party cooperation and boilers, our company is the right choice to make, party fast to the products we offer very environmentally friendly characteristics, and has high efficiency, for my company save a lot of costs. --customer feedback
The sale of the burner type and range of applications markets burner has a range of many different types, different types of burners applied are not the same. The scope of application of the burner more extensive, can be applied to the engine and ignition stove, and it appears to people's lives has brought great convenience, it has been a lot of consumers like. Burner also known as integrated burner to oil and gas-based. Fuel is generally used in small and medium sized boilers, the fuel fan heater, baked (baked) and the small fuel tank furnace. Broadly speaking, civil stove, lighter, torch, engine burner means belong to the scope and special civil combustor burner. Flame atomizer a pre-mixed component structure, also known as combustion head. It is a mixed gas of the combustion flame jets and carriers like sample, more than a single slit type slot length of about 50mm and 100mm there are two kinds, slit width 0.5mm, the former for the nitrous oxide - acetylene flame, after by an air - acetylene flame. Generally made of stainless steel, but also of aluminum or brass. A single slit (single-slot) with three slits (three-slot) two kinds. Mike atomic fluorescence spectrometry using a burner (Mekerburner), which is shaped torch flame. Two kinds of sub-cooled and air-cooled. After washing with distilled water is often required to use, to prevent corrosion and plugging the gap.
Electric steam boiler before use Preparation 1, the operator must understand how the present electric steam boiler, location, performance and working methods of the various accessories. 2, check oil combustion, and each nozzle connection, power supply and the burner, the pump, the boiler installation accessory. 3, clearly the main steam valve open, after closing the normal close it. 4, check the electric steam boiler water level, water level confirmation flexible, normal position. 5, the pressure regulator is properly tuned, regulate combustion damper.Free Chat
Copyright © 2020.Company name All rights reserved.